Table of Contents

How to Clean a Foam Filter on a Shark Vacuum, So It Lasts Longer

Keeping the vacuum filter clean is important if you want to keep your carpets and upholstery looking new. A dirty, clogged filter can cause a vacuum to lose suction and allow dirt and hair to escape back into the air. This is more common on hard surfaces, such as carpets and upholstery. Over time, the foam filter in your Shark vacuum can become clogged with dirt and debris, reducing the suction power. This is a guide on cleaning the foam filter in your Shark vacuum cleaner. Luckily, it is pretty simple to clean a foam filter on a shark vacuum.

Foam filters are an important part of the vacuum that helps to keep dirt and dust out of the air by catching them. Unfortunately, these filters often get dirty over time and need to be cleaned. Your vacuum will run efficiently, and your home will stay clean when you clean your filter!

When the filter becomes dirty, it will reduce suction, which could cause an issue with your vacuum’s performance. To clean your filter, you need to remove the front cover and filter from the machine. You then rinse or scrub the filter off and place it back into position on your vacuum cleaner.

Here are some steps:

Make Sure the Vacuum is Turned Off

Before you clean a foam filter on a Shark vacuum, make sure the vacuum is off, and your vacuum isn’t being used. Turning off your vacuum is important because it allows you to use it at the same level as when it ran, without the suction from the filter being used. Once the vacuum is off, put the vacuum on the floor, and leave it there. Check the vacuum often to ensure it is still turned off but not in use.

If the vacuum is turned off but the filter is still clogged, it will filter clogged air and eventually clog itself. Take out the Shark vacuum filter and soak it in vinegar. Baking soda can also be used to soak the filter, as well. Once the vacuum is out of use, remove the filter and soak it in vinegar or baking soda.

Cut the Foam Filter to Fit

If you are using a Shark vacuum cleaner, find the filter’s hole. Grab a tool, such as a utility knife or screwdriver, to cut out the filter and clean it. The tool has to be flexible, though, so it can handle the sharp blades on the Shark vacuum’s cleaner head. Hold the tool’s cutting edge with your other hand to protect it.

To remove the foam filter, place the knife blade at the bottom and push it down until you can pick it up and remove it. Then, you can either rinse the filter with a clean, wet cloth or spray cleaning solution onto it. Wipe away any debris, so it is ready to go.

How to maintain the filter for sharks

It is important to maintain the filter for sharks.

1. The first thing you need to do is ensure a guard on top of the filter. A clogged filter will be prevented from collecting gravel, which will stop it from working correctly.

2. You also need to test your water quality monthly and make sure it falls within the parameters set by your aquarium manufacturer’s guidelines. This will ensure that your filter can function properly.

3. Lastly, make sure you keep up with maintenance as recommended by your manufacturer guidelines and clean your filters as instructed according to what you have been told.

How to Wash Your Shark Vacuum

If you don’t have the Shark vacuum, you can clean the foam filter with some household cleaning products on a traditional vacuum cleaner.

Clean the Foam Filter on a Shark Vacuum

Before you clean the foam filter on a Shark vacuum, be sure to empty the unit. Shake out any loose particles, remove any obstruction from the bag, and replace the bag. Even if you aren’t planning on using your vacuum for the rest of the week, you want it to look brand new before you clean it.

Fill your Shark Vacuum with purified water and turn it on. Fill the brush chamber with water and apply an abrasive cleaning pad or paper towel to clean the foam filter. Make sure you use the tip of the pad inside the filter. Carefully remove the filter to inspect the foam filter, making sure to wear goggles and gloves. You should not touch the filter with your fingers. If you see any sign of dried or burnt gunk, remove the filter again and repeat the process.

Check for Signs of Clogging Again

To clean your vacuum, you first need to check for signs of clogging again. This can be done on all Shark vacuum models and every Shark vacuum model, for that matter. The Shark app is your first stop if you have one. This will allow you to monitor the vacuum while you run it. Go to the Shark vacuum app and open the “Vacuum” tab. If there is any light or color around the vacuum, that means it’s dirty.

Clean Out the Dirt and Hair Inside the Shark Vacuum

Pull the Shark vacuum hose out from the wall as a first step. Find the clean part of the hose and pull on it until you feel resistance. You are usually in good shape when you pull on it hard enough to move. Pull-on it again, so the same resistance shows up on the vacuum.

Conclusion

So in this article, I hope you got the answer to your query “How to clean foam filter on shark vacuum.” Don’t forget to give the Shark vacuum cleaner a good cleaning from time to time. The Shark vacuum comes with an auto-flush feature that’s great when cleaning carpet and hard surfaces. Plus, a separate cloth can be used for the attachments on the handle, which will keep them in good condition for a long time.